(800) 853-2651
SHOP NOW

Search results

  1. O

    Why aren't I getting

    E-mail notifications when someone post to a post I answered??
  2. O

    Steering seal under the steering wheel

    Would any body happen to have the seal number?? I figure once I pull the seal out that I'll have nothing to go by other then what is left of the burnt part of the seal that is left from it catching fire
  3. O

    IH584 steering seal

    Just under the steering where I have a bad hyd oil leak. I'm wondering if I could pull the steering wheel off and get to the seal and pull it and match it to a seal that would fit. This is on the IH584 I was given a few years back and it had burned and that area was so hot the only thing left...
  4. O

    More info on the IH2250 loader

    I just measured the bucket pin holes the upper ones and close it was 27 inches center to center and open it was 48 inches. Going to call surplus supply and see what they have with a rod diameter of more then 1 inch.
  5. O

    International 2250 loader cylinder spec

    So the 2250 loader on my IH584 has cylinder problems. O bent one of the 2 bucket cylinders a couple years ago and the cylinder on it now are not working as they should. I want to replace the cylinder with one with bigger shaft diameter so I will not bend another one. So does any body kno0w the...
  6. O

    Unable to get to the site

    By way of the e-mail links I receive when some one answers a post. It come up with not being to go to the site
  7. O

    Odd running problem part 2

    So I rebuilt the carb this afternoon and put it back on. After getting the setting where the engine like them we graded my mile long driveway with no engine problem. We did how ever have a traction problem from time to time due the the new cutting edge and the fact the blade if now about 10 inch...
  8. O

    Odd running problem

    So yesterday I put a new cutting edge on my W Speed Patrol. I then started it up to move it around so I could cut the extra part of the cutting edge off and it would run for a bit then start coughing and acting up and popping back from the intake of the carb. I got it where I need it to cut the...
  9. O

    Well the old Troy built tiller

    Did it's job today. It did take a little bit to get it going like pulling the air cleaner off and holding my hand over the intake but once I did that it fired up and ran till I let it run out of gas and I tilled about 3/4 of my garden. Sort of seemed odd that the ground seems to be sort of wet...
  10. O

    Do they make an easy fill power steering cover??

    I have a Ford 841S with power steering and loader. To fill it up with fluid you have to pull the top cover which is a real pain due to the loader being on it. So do they make a cover that has a cap in the cover so you can take the cap off and fill it up?
    • old
    • Thread
    • Replies: 18
    • Forum: Ford
  11. O

    What model is it

    Work on a JD today had a 6 cylinder gas engine serial number is SNT221R115172R. The owner want me to get it running if I can. Did pretty much figure that it had a locked up engine and it needs plug wires since it has none. We put a battery on it and I then used a screw driver to short across...
  12. O

    So where they worth it sockets

    I stopped at a consignment store today and picked up a bag of mis. sockets. 29 where 1/2 inch drive about half deep well and the rest short ones. Plus 13 3/8 drive. I paid $10 for them all
  13. O

    Clearing history worked

    So I just cleared my history on my old computer so I can now get to the forums again Thanks
  14. O

    Odd how one computer work but not the other

    So the omputer I have trouble using the keyboard on works but my old one doesn't work now
  15. O

    Good/bad of a Dewalt generator

    Says 8125 starting and 6500 running. Bomgaar's has it on sale for $969.99 till the 24th. So are they any good?? I know it is not big enough to power the whole house but it would get me by if/when needed
  16. O

    Site seems to be very slow

    I go to a post and click on it and it can take almost a minute for it to go to the post.
  17. O

    Spammer

    In tractor talk going by luckywhite and he/she has at least 4 post
  18. O

    F20 up for aution

    at lake area liquidations.Com All it is is parts but some one might be able to use it. It was on rubber but the tires are shot. They also have a 1930 Mercury car that will be up for auction. Suicide doors by the way. By the way this is an on line auction place
  19. O

    Re:

    Yes you can but why the narrow 19 inch tires tend to dig in and not turn as easy as the 16 inch one do. Plus they cost more and are harder to find
  20. O

    Back to the 584 loss or steering

    So got a chance to look at it today. I removed a side cover and started it up. Had hyd fluid shooting out of a broken fitting. Fitting is in a hard line going to the steering column area under the steering wheel. Seem the fitting broke off the hard line. Hope I can find a hyd hose that will...
Tractor Parts Tractor Manuals

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top