(800) 853-2651
SHOP NOW

Search results

  1. mikewood869

    Kory 5566 running gear wheel bearings

    I decided to repack the wheel bearings on a Kory 5566 running gear and add some grease zerks. I took off the front left hub and the inner bearing in the hub spun. I got the bearing not to spin. Anyways... Anyone know if there is supposed to be a gap between the bearing and the seal? There is...
  2. mikewood869

    1980 Ford F700 370 engine to 1995 Ford 429 engine

    Looking to swap a 1980 370 to a 1995 Ford 429, is there anything to watch out for? I assume just pull off most of the wires so I can get spark
  3. mikewood869

    Ford 3400 power steering cylinder line seal

    Anyone know if you could if this seal or ring is supposed to come out? I was working on the right cylinder and one of the ring/ seals were missing. Part number: 358774S, 4a. The picture is the left cylinder. Power steering cylinder diagram
  4. mikewood869

    Ford 3000 Holley carb, what’s it’s made out of

    Anyone know if you could wield on a Holley carb r11411a. Is it aluminum or white metal?
  5. mikewood869

    Ford 3400 power steering cylinder and lines

    Before I put a 3400 power steering cylinder back on a Ford 3000 tractor to see if it works, does anyone know if the cylinder rod when extended, will be too long? This is on a 3000 style front end. Also I still don't have one of the cylinders yet (having it rebuilt since I couldn't get it apart)...
  6. mikewood869

    Holley carb model

    Anyone know what model Holley carb would have came on a 1966 Ford 3000. I put that carb on a Ford 4500 4 years back. I ended up getting bad fuel in the tank, I think I’m going to need to crack it in half possibly (tractor ran with half choke in any rpm crappy) Ford 4500 running crappy
  7. mikewood869

    ID a Ford engine

    Anyone know what engine this is? Its got a turbo. This was on the right side of the engine, right where the block and oil pan meet. It’s in a Ford 755a and the engine was swapped out at one point. Also the tag on the hood
  8. mikewood869

    1944 John deere A pedestal

    Anyone know if a pedestal from a 1950 John Deere A would fit on a 1944 John Deere A? I'm think that the holes are in different spots
  9. mikewood869

    Ford 755a log splitter

    Anyone know what the hydraulic flow off a Ford 755a hydraulic pump is? I'm thinking of making a log splitter for the backhoe. The cylinder I'm probably going to use is off of a Ford 740 loader (dump cylinder). I'm hoping it would make splitting 30" logs easier.
  10. mikewood869

    1970 Ford 3400 power steering pump pressure

    I have a power steering pump from a 1970 3400 (pump reservoir style), does anyone know what pressure it s supposed to put out. I m looking to rob the pressure relief valve and put it into a 3000 power steering pump (pump reservoir style) This post was edited by mikewood869 on 11/30/2023 at...
  11. mikewood869

    1966 Ford 3000 power steering cylinders

    Anyone know the cylinder size for a 1966 Ford 3000 power steering cylinder? I'm not sure if they have ones for different years.
  12. mikewood869

    Hay conveyer 90 degree bends

    Anyone know if they still make hay conveyer 90 degree bends?
  13. mikewood869

    New Holland 415 disbine 1000 to 540

    We ended up getting the New Holland 415 discbine with 1000 pto. The rollers don't seem bad, just the cutter bar. A owner apparently ran a fence post over and took the teeth off of 3 gears (could be more but 5 of the turtles still turns with no slop). The gears didn't crack just lost teeth. We...
  14. mikewood869

    Ford 6610 1000 pto

    Anyone know if I can swap out a 540 shaft for a 1000 shaft? The tractor is a 6610 with the 8x4 transmission
  15. mikewood869

    New holland 415 disbine

    Probably going to look at a New Holland 415 discbine in the near future, anything I should look out for? Anyone know what the HP requirement is? Apparently 2 of the turtles don’t turn. I’m planning on running it on the Ford 6610. This post was edited by mikewood869 on 10/19/2023 at 04:44 am.
  16. mikewood869

    Ford 2910, draining injection pump

    Anyone know a way of draining the fuel out a injection all the way? Let a neighbor borrow the tractor and they filled the tank with gasoline. Gasoline got past the fuel filters and killed the filters it looks like.
  17. mikewood869

    Parts baler for kicker parts

    End up getting another 315 baler for parts, but with a 70 belt thrower, we already swapped the stub axle and pto over tonight, next is pulling off the Wisconsin, then figure out how to put a NH 75 pan kicker on it. Ran the baler for the 1st and last time for 2 minutes. Got lucky and the plunger...
  18. mikewood869

    New Holland 75 pan kicker gap questions

    Anyone know if there are shims for the brackets to put on a 75 pan kicker? There s about a 1/4" gap on both sides of the top, bottom and middle bracket (also hitch brackets too)? Looks like washers or cut a piece of metal so far? This kicker is going on a 315 that didn t have a kicker before...
  19. mikewood869

    New Holland 75 bale thrower

    Anyone happen to have any photos how one is attached to the baler, including the hydraulic reservoir? We just bought one and are getting ready to put it on a NH 315. This baler came off of a 316. This post was edited by mikewood869 on 08/09/2023 at 07:09 pm.
  20. mikewood869

    New Holland 315 bale chamber size

    Anyone know what the chamber size on a New Holland 315 baler is? Is it a 14x18 or 16x18?
Tractor Parts Tractor Manuals

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top