(800) 853-2651
SHOP NOW

Search results

  1. Joe Ferguson

    Little rods in snow blower chute

    Does somebody knows what is the pourpose of the little rods in some snow blower chute. Thanks in advance Joe
  2. Joe Ferguson

    MF-1428V electric PTO clutch

    Just bough an MF-1428V. There is an electric engagement power take off. I plan to use it with my wood chipper which has an 300 lbs flywheel. Will it damage the PTO electric clutch mechanism to start the chipper with such big inertia? Thanks in advance
  3. Joe Ferguson

    Fuel system blleding procedure Iseki 3 cylinders engine

    Does somebody have the bleeding procedure or where to find it. I have the repair manual for the engine but it is not mentionned. Thanks in advance Joe
  4. Joe Ferguson

    Fuel system bleeding procedure 3 cylinders Iseki engine

    Does somebody have the bleeding procedure or where to find it. I have the repair manual for the engine but it is not mentionned. Thanks in advance Joe
  5. Joe Ferguson

    Electric power take off

    Just bough an MF-1428V. There is an electric engagement power take off. I plan to use it with my wood chipper which use an 300 lbs flywheel. Will it damage the PTO electric clutch mechanism to start the chipper with such big inertia? Thans in advance Joe
  6. Joe Ferguson

    Opinions on MF-1428

    There is an MF-1428 for sale near me, I would like to have opinions on that tractor. Priced $17000/Can 4X4 with cab and front snow blower Parts availability etc Thanks in advance Joe
  7. Joe Ferguson

    Weird idea MF-50 charging diagnostic

    A weird idea came in mind this morning. No battery charging in my MF-50. Is there a manner to connect a 12 volt power supply or battery charger to the ARM or/and FIELD wire from the generator to the control box to simulate the generator in order to see if the control box is good. I have no acces...
  8. Joe Ferguson

    Less tractors for sale in photo ads

    As the time pass I see less and less tractors for sale in photo ads. I think there are less old tractor enthousiasts like me. I am curious to see the age average of this formum members. It may be because we learned or used these tractors when we were young. The interest in old tractors and...
  9. Joe Ferguson

    New forum configuration

    I would like to say a big thank you to the administrators an programmer(s) of this site. It is now possible to zoom on the pictures...great improvement. Thanks again ! Joe
  10. Joe Ferguson

    MF-50 link segmented belt

    I have an MF-50 gas Z-145 engine with front mounted hydraulic pump for the loader. I plan to install an alternator. The fan belt is badly worn and I would like to replace it without disconnect the pump drive shaft. A link segmented belt should be the solution. Does somebody knows the correct...
  11. Joe Ferguson

    Year that PTO shaft changed from 1 1/8 to 1 3/8

    Does someone knows what model or year Ferguson or MHF or MF changed PTO shaft diameter from 1 1/8 to 1 3/8 Thanks in advance
  12. Joe Ferguson

    TO-35 gas broken rocker shaft support

    Opened the valve cover discovered the two front rocker shaft supports broken and the rocker shaft broken in two. Is it a frequent problem on Continental Z-134 ? and what might had caused that ? Thanks in advance Bart
  13. Joe Ferguson

    MF-1547 good ?

    I'm looking for an MF-1547 with independent belly PTO and front snow blower does somebody has experience with this model ? Thanks in advance Joe Ferguson
  14. Joe Ferguson

    1966 Ford 2000 diesel 3 cyl cooling problem

    Was blowing snow then suddenly spitted antifreeze from the radiator overflow tube. No indication on the temperature gauge which previouly indicated 185. I slowly opened the radiator cap and heard "goble goble" as it has air escaping inside rad. No longer heat in the cab heater hoses. Fan belt...
  15. Joe Ferguson

    1966 Ford 2000 3 cyl diesel clutch pedal adjust

    Live PTO model. The pedal freeplay stop screw dissapeared from the actuator lever. I looked in New Holland parts site, it is not displayed. Does somebody knows the specifications of this screw and jam nut. (lengh..diameter..thread pitch) Thanks in advance Joe Ferguson
  16. Joe Ferguson

    Anadolu power steering adjustment

    On a 1966 Ford 2000 3 cyl diesel with Anadolu add-on power steering. It is little hard to turn left. There is an Allen head bolt with locking nut adjustment?) ont the actuator valve on the cylinder the bolt pass trough a slide probably to avoid valve tipping. Is this bolt is an adjustment or...
  17. Joe Ferguson

    Hydraulics question

    Have a 1965 Ford 2000 diesel 3 cyl tractor with FEL. Hydraulic very slow in cold climate. When I operate the loader after engine warm-up once it has raised few inches it operates at normal speed and the bucket cylinder operates normaly. But if I put it down completely it takes 30 seconds to 1...
  18. Joe Ferguson

    Cold climate hydraulic oil Ford 2000 diesel 3 cyl

    I recently bough a Ford 2000 diesel 3 cyl with a front mounted snow blower. The previous owner dont know which oil in the differential/hydraulic system. There are hydraulic cylinders for blower lift...chute turn...chute deflector which are very slow when oil is cold. it begins to operate...
  19. Joe Ferguson

    Ford 2000 Hydraulic oil for winter

    Bough a 1967 Ford 2000 3 cyl diesel last year. Last winter had to run the engine 15 to 30 minutes before the hydraulics starts to work. Worked normally after 1 hour. Would like to know what hydraulic oil to use to have instant hydraulic operation in winter. This tractor is used in winter only...
  20. Joe Ferguson

    Big draft control spring Foerd 2000

    Recently bough a Ford 2000 diesel with front mounted snow blower. Bough from an estate. The p/o removed the 3 point arms to install the PTO mechanism for the front blower. The big draft spring was also removed. The blower lift turn and chute cylinders are operated from the original hydraulic...
Tractor Parts Tractor Manuals

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top