(800) 853-2651
SHOP NOW

Search results

  1. T

    Different 3020 Overhaul Question

    Later (1969) 3020 LP. Have been on a search for Pistons, rings and liners with no luck. Pretty sure the 4.25 propane (flat top) pistons are made from unobtainium, have resorted to going to regular gas pistons.....any ideas?
  2. T

    Long Shot

    Looking for a set of 4 pistons for a LATE 3020 LP Part number AR44093
  3. T

    Re: Trucker Drivers and transmission Challenge.... Can

    Years ago I was hauling corn from the combine for my Brother in Law, neighbour that did his combining supplied the trucks. I went to grab a loaded truck one night about 11 pm, a fairly elderly Fargo with a 5 and 4 only to find the clutch pedal stayed on the floor after stepping on it. Owner...
  4. T

    Tim S

    Trying to reach you by phone......did you run over it?
  5. T

    467 Baler Question for Tx Jim

    Neighbour has a 467 which has started applying surface wrap before the bale is full. It often happens when turning on the headland which would make me think its a harness issue so I have told them to inspect that. It did it once in the middle of a pass but it is a very rough pasture they are...
  6. T

    MD Reproduction Parts

    Talked to them 10 days ago can't reach them now....holidays? Anyone have info? Thanks
  7. T

    Buickanddeere

    The post about the splitter hydraulics was getting tired so I started a new one......It seems Mannheim/Dubuque hydraulics are a topic which can be hard to grasp. Yes many people on here are talented but many are also users of the machines not repair experts. I posted the kit number that would...
  8. T

    Window Seals

    Had a request from a collector who is looking for a source for the window seals as used in the cabs on the pre- Generation II tractors. Any ideas? Thanks.
  9. T

    To Tx Jim

    Did you and your neighbour get the 2130 sorted out?
  10. T

    Crankshaft Seal

    I am doing some repairs to a customers 1020 John Deere, including replacing the clutch. As a matter of course I remove the flywheel to check the rear crank seal....its wet, time to replace. By the serial # this should use the newer type seal but it actually requires the T20326 seal......ONLY...
  11. T

    New Holland Weigh Command Diagnosis

    Neighbour has a New Holland Grinder Mixer with Weigh Command that is reading "Lockup" I have no experience with this system, anyone have a suggestion? Thanks.
  12. T

    JD 250 Skid Steer

    We are installing a cab heater in this machine and cannot sort out the proper connections for the heater hoses to the engine. Has anyone done this? Thanks for any input.
  13. T

    I am Ready to Burn this FSM

    Frustration is overcoming me here. This Major came to my shop with a tired injection pump (Simms Pneumatic Govenor), it would not idle and ran poorly at high end. I checked the fuel supply etc. before removing the injection pump and in my haste did not take note of timing marks prior to...
  14. T

    Fordson Super Major Injection Pump intallation/Timing

    Hello all; It has been a frustrating day.....Power went off at 5:30 this morning and has only recently came back on, I have not eaten enough, its very hot and humid and I am not thinking clearly to get this problem sorted out. I have here a Super Major that had injection pump issues. I was in a...
  15. T

    Question for John T OT

    Ok I use this camper trailer to attend tractor shows so it is kinda sorta on topic. I have a 2005 Trail Lite camper that we really enjoy other than an electrical gremlin or two. We last used it 3 weeks ago and after it being plugged in for a few weeks prior to heading out we drained the...
  16. T

    John Deere A Starter

    I am working on a John Deere A (1943) and am in need of one brush holder spring. The Delco number for the spring is 34846, the starter is a Delco 1108914. Any information is appreciated.
  17. T

    520 Oil Line

    I am working on a 520 tractor that has a broken oil line, it runs from the oil pump up to the front side of the main case and feeds the rocker arm shaft. The part number is AB5046R and is no longer available. Is it possible to get this line made at a diesel shop?
  18. T

    1020 Industrial

    Looking for info regarding this model, NOT 300
  19. T

    Re: hydraulic problems JD 2350

    Have a look in through the transmission oil filler cap to see if there is oil running/spraying at the front of the rockshaft housing. If so you will need to remove the rockshaft and repair the leak at the hitch valve. The kit for this job is JD part # AL57974
  20. T

    Um No

    In the photo ads, 1974 John Deere 830 with Perkins Diesel
Tractor Parts Tractor Manuals

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top