(800) 853-2651
SHOP NOW

Search results

  1. S

    is this a ford car rim?

    Found this buried on my aunt's farm. Thanks
  2. S

    OT: Had to show the kiddies how to turn a wrench

    So I'm setting at my desk working and the owner walks in from the shop. Our new 20something year old mechanic can't get a big c clip off a retainer pin to remove a hyd cyl from a rubber tire backhoe. No problem, walk out. Of course it's an inside clip between the loader boom and the engine...
  3. S

    Re:

    if it has a 12v coil and resistors needed, or a 6v coil and resistors needed for 12v, your cheapest fix is to hang a 30$ alternator on it and go.
  4. S

    OT - interior and dash lighting issues on a 2007 gmc 2500

    At work we have a 2007 gmc 2500 diesel. We did a partial dash removal to work on the steering column. Put back together. dash indicator lights ( battery, brakes, etc ) all work. LED odometer works. Dash illumination that comes on with the headlamps does not work, overhead dome lamp and...
  5. S

    alemite 0820-B grease pump - diagram?

    Anyone got a diagram or any part numbers for this air operated grease pump. It is a 50:1 unit.. and I have 2.. One quit a few years back and it's been in the corner.. the other just quit. I went to Alemite's site and could not find any documentation. Thanks
  6. S

    checking in from central florida

    Getting rough here.. No fuel... no utilities of any kind... spotty cell service.
  7. S

    OT rant.. MTD mower deck spindles

    Don't they harden them things.. any? pulled the blade nutz off a 13mo old mtd to change out the factory blades ( 12m warranty mind ya.. ). Whatever metric ultra fine thread they used to be, came right off in the nut using a 3/8" butterfly ( palm ) impact gun set to low. My ARM makes more...
  8. S

    ot/ western star tractor cat engine, cuts off

    Just got a call from work. Our western star tractor cut off at an intersection, driver said no sputter, just like cutting key off. Would not restart that instant, so driver put his triangles out and checked again. In the 2? Minutes of putting triangles out, it started up like normal...
  9. S

    Re: Spark Arrestor for 8N ?

    if you frequently drive slow or park in tall dry grass with your 8n, you could go with a vertical exhaust...
  10. S

    Re: 52 8N - bad coil?...or cap?

    1, your battery is likely dead, remove cables and charge it. 2, starts, runs, dies, restarts. Guess what.. That's not timing, nor is it the condensor. Open condensors burn points, yours ain't or it wouldn't have kept starting. Shorted condensors prevent spark. Starts dies,vrestarts? FUEL...
  11. S

    Re: Attach bearing retainer eyelet to steering shaft on Ford

    In the end, the retainer is just fir quick easy assembly. The bearing is 100% captive with worm gear installed in cover and thrust set correctly.
  12. S

    florida and southeast coast members

    Next day and a half will tell us alot. I filled up the diesel truck, and will grab 10g gas today to feed the loader tractor or another to run the pto Gen. Got some spam n tuna in the house already, animal feed is good. Good luck to us.
  13. S

    Re: 8n tractor

    first decide if it is a linkage or a governor issue. go to the carb. notice a rod from the carb to the gov. notice a rod from the gov to that hand throttle. does moving the rod from the gov to the carb ( increase rpm ), does the gov try to tug back on it to slow it down?
  14. S

    need info on this machine

    My brother sent me this pic, asked me if I knew anything about them. Pro/con, year, etc. Thanks
  15. S

    main and rod bearings on a G, question

    I pulled a main and rod bearing out of a G this weekend. any way to tell if these are standard or not. ( shells don't have a standard mark, or a size over, that I recognize anyway ), etc. main 3632B020N rod 3638B030N can anyone tell me what I have got? thanks
  16. S

    os 3000 power steering

    Was talking to petra/ron ( infrequent poster here ) today about his early 3000 with power steering. ( separate resevoir ). makes less than 100 psi. he said he can screw the cap on the relief spring down by hand.. that sounds wrong. anyone got specs on the spring?
  17. S

    3000 ps line question

    Helping a buddy out a basket case 66 3000 back together. Ok os with separate resevoir up top. Steering hard to right. Before we take the ring apart to see broke springs, just checking lines. Appears both side are the same as far as, the line closest to the front from the column both go to the...
  18. S

    need 2 groove ballancer pulley for industrial 300 6 cyl 1980

    At work we have a 1980 300 6 cyl industrial engine, doing a rebuild and need a ballancer pulley. 2 groove. Rebuilder could only find a 3 groove one.. but that won't work as we have extra accessory drive on the front and the spaceing on that 2 groove is needed. ford oval on the ballancer ( 3...
  19. S

    oil filter question on a cat D8

    Was going over our oil fitler charts here at work and noticed we are buying Napa 1161 filters for our cat D8 ( takes 2 - cartridge canister types) From Napa, those list as transmission filters. going back to the original cat # of: 5S484 I find lots of crosses... donaldson, fram, baldwin...
  20. S

    tranny oil fill on a 06 international 5500 dump???

    sorry for the OT.. but I'm out servicing the dump truck and can't for the life of me find a fill for the tranny!! Anyone got a diagram or got one and knows where to look. found drain ( pita spot too ) and another port.. but no way to get a hose to the darm thing. thanks
Tractor Parts Tractor Manuals

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top