(800) 853-2651
SHOP NOW

Search results

  1. A

    Ol' Ollie 1850 LP - SMOOTH POWER

    Yes in WI
  2. A

    Ol' Ollie 1850 LP - SMOOTH POWER

    I've had 2 Oliver 770 LP's for sale for over a year. Nobody seems interested. Used them to run feed mixers and feed cows for 35 years. Nice for inside work ,start good in winter,and fuel is half price. Fueling is not hard if you vent correctly. $5000 for two .
  3. A

    New Idea 218 Manure Spreader Skipping

    Watch while operating under load. Check for looseness of Pawl arm bushing (12) and if Main apron shaft bushings are too loose (shaft going up and down}
  4. A

    7000 planter question

    The bracket is to keep wheel from picking up stones.
  5. A

    7000 planter question

  6. A

    Want to run belted equipment only have PTO

    There are lots of 90 degree gearbox flat berlt pulleys that bolt over the pto available and for running mountet pickers a large V pulley was fitted directly to the pto shaft.
  7. A

    ford 5000 new engine? Any advice on where to get?

    I believe one of best Ford tractor engine rebuilders is Farmland Tractor Tangent OR ,a ways S of you. I got an 8670 rebuilt engine from them about 7years ago and was well satisfied ,even though I paid freight for engine exchange from WI.
  8. A

    ford 5000 new engine? Any advice on where to get?

  9. A

    american motors corp.

    I had a 1961 Rambler ,probably the best of the compacts,. Six passenger , Six cylinder with overdrive ,fast and got 25 mpg .
  10. A

    as a kid

    As a kid I loved being around my uncle neighbors during threshing with a DC running a Case threshing machine and baleing with a Case wire hand tie baler. Fortunately never had to ride on the baler doing the tieing,
  11. A

    9600 Question

    Just throttle down a bit and save fuel.I had two of them back in the 70's. One without cab and one with.Had to be careful to keep the rear axle U-bolts tight. They have a dry clutch which may have to be replaced.
  12. A

    Wednesday Motor

    One of those listed on Craigs list Janesville WI today.Is a 1952 Truck commercial power unit with a 4speed transmission.$1500. Seller claims they were going to repower an 8N ,but sold tractor.
  13. A

    historicaly, what was the worst ford tractor made?

    The 6000 ? It had most of the features of the JD 4010 with the power shift a few years and 2 speeds ahead but wasn't ready for production. The power shift engineer went to JD.
  14. A

    Re: Leyland

    Tkank's for correcting the factory location. I thought it was in SW Scotland. I like the Leyland 384 and 270 that I have,but their design of the final drive ,brakes ,and pto-hydraulic was old. No planetary drive and wet disc brakes and pto clutch also shuts off hydraulics.
  15. A

    Leyland

    I have two,384 and 270,built in Basildorf Scotland,about 1970 and imported thru Miller Supply ,St Nazianz WI as cheaper power. One carried two 200 gal saddle tanks and was my sprayer and planter tractor for years.Now I just use it for mowing fence rows and spraying.Comparable to 5000 Ford ,60...
  16. A

    Soybeans '23

    Just starting this evening. My S WI 2.6 Enlist beans look about like yours . Too many small beans. Not as tall as yours and 51 bu yield poorest in many years.Not much rain after planting. The Oliver Acreage is out combining soybeans Maybe he'll get a video...
  17. A

    1660 2 speed hydro?

    i.I had a 1660 about that age, and it was 2 WD. It hat a 3 speed transmission and went close to 20 mph . only i speed hydro. If rear steering is loose can be tricky to drive that fast.
  18. A

    Cutting a rubber mat

    I've cut them with a handsaw. Easy if you have some way to pull the mat apart as you cut.
  19. A

    Cutting a rubber mat

    I've cut them with a hand saw. Easy if you have some way to pull the mat apart as you cut.
  20. A

    New Idea Manure Spreader Parts

    Regarding 217 spreader parts, I have a left side front apron idler, well used , 3 ratchet pawls ,and one beater paddle .For a 245 I have a complete set of wheel bearings and the bogie wheel pivot bushings.For the newer 3600 series ,a left side apron idler ,new and two piece welded ,and a beater...
Tractor Parts Tractor Manuals

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top