(800) 853-2651
SHOP NOW

Search results

  1. L

    Need help with jubilee

    Coils and wiring thoughts. Coils may be true 12 volt, 12 volt resistor required (basically 6 volt coil}, or original 6 volt coil with ballast resistor installed (very common on conversions). If a true 12 volt coil is used with a resistor, a very weak spark will result. Quick visual check is...
  2. L

    Help - Using 8N Pull Type Brush Hog

    SAFETY ALERT make sure you have an over running device on the PTO. Fly wheel effect of shredder will keep pushing you when clutch is disengaged without one until you get transmission or PTO out of gear.
  3. L

    Fixture for tapping threads

    My Tee tap handle has a center hole on back side. I pull drill bit and put a dowel pin ground to a 60 degree center in chuck and follow tap handle with center until started straight. most taps over 1/2 inch have a center in tap that can be used the same way turning tap with tap handle or a...
  4. L

    Ford 3600 gas Governor problem?

    Suggest checking fuel flow to the carb. Disconnect fuel line, I'm thinking most here say 1 pint in 2 minutes for minimum.
  5. L

    Curious about a couple of tool finds

    Welder should have copper windings, I'm guessing mid 50's to mid 60's good AC welder. Googled vise, every thing I see says excellent unit but it does not take much to beat out Chijunk
  6. L

    Short in Ford Jubilee?

    Start by cleaning battery cable connections including ground to tractor end.
  7. L

    British Made IH

    Had 695 at work, also bradford built
  8. L

    rotary converter question

    Some one told me you should derate motor size by 1/3 for full load capacity if using a converter. In other words do not put over a 6 1/2 horse load on a 10 horse motor. Experts advise appreciated for confirmation. Leroy
  9. L

    injector pump problems

    properly bled all the way to injectors?
  10. L

    What size is M24X2 Castle Nut?

    36mm is 1.417 inches 20 thousandths smaller than 1 and 7/16 inches, if you have a 6 point socket you can probably get by using it.
  11. L

    Dowsing Rods

    Story about first irrigation well in this area. Driller and farmer walking around on farm field discussing where to drill test hole and sipping a six pack of their favorite beverage, nature called and driller said water draws to water, did the required, marked location and drilled test the next...
  12. L

    1965 Ford 5000 water pump bearing and seal replacement

    This site sells water pumps for Fords. go to top of page and click on parts then Ford and cooling system
  13. L

    Looking for another idea.

    2 unlikely possible things. Can you look in the radiator fill when running for good circulation? If so it should return from top hose and flow down thru radiator, exception is cross flow but still return from top hose. I have had an impeller loose on the shaft (1964 Chrysler, known problem years...
  14. L

    jD 4219 missing at idle

    To much juice causes cracked pistons, broken ring grooves, broken rings, result low compression. Hope it is not any of the listed items.
  15. L

    4 1/2 in grinding discs

    I suggest you read up on Norton Norzon Plus grinding disc. Very aggresive, expensive, long life. Probably available from industrial or welding supplier. I prefer them if I have to move metal however they take power, I use a Milwauke 4 1/2 inch not a bargin counter 19.95 special.
  16. L

    Can anyone I.D. this water pump?

    Checked gasket part #, came up with Allis Chalmers which purchased Buda engine company. Referenced 4B153, 4B18?, 6B230, 6B273 engines. Checked my Cockshutt/Coop 30 with 153 engine and it appears to be similar except for length which I cannot determine from picture. these engines were used in...
  17. L

    Ford 172 diesel squealing noise, no oil pressure, loose harmonic balancer bolt, and white smoke out of breather

    Apply a little choke, if it smooths out some that is an indication of dirty carb or if it has a load adjustment open it a little. Condition of points? possible cracked or carbon tracked distributor cap? Suggest doing diagnostics not throwing parts at it. I ran soil sampling drill rigs that used...
  18. L

    Those vintage old steel track attachments that went over rubber tires on tractors

    Years back there were tracks available to go on Bobcat skid loaders over the tires. It's possible that's what you saw.
  19. L

    Valve lash on kohler ch23s

    George: the question was for a model CH23S which I referenced to the FACTory Manual. it was not for some other model and series of engine. It appears to me you only read Kohler and 23 assuming it was a different engine not as specified in the original question.
  20. L

    Valve lash on kohler ch23s

    George READ the first five words I posted for FACT. If you can't believe the factory manual there must be a problem on your end. Leroy
Tractor Parts Tractor Manuals

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top