(800) 853-2651
SHOP NOW

Search results

  1. F

    Cummins p pump question

    Have the pump off the engine. The rack is moving about .250” as viewed through the end plug. Pressurized the head and all six delivery valves are leaking… will not even hold 5> psi. Should they not hold at least a little bit? The engine had been idling and just quit ( after fuel filter...
  2. F

    For RTR… flat planter chain

    Hope this isn’t too political…
  3. F

    There any Hobart experts out there?

    My old 100 amp Century wire feed went down recently, so I borrowed a Hobart Handler 175 that was sitting unused in a barn for a few years. Im running 023 wire with 80/20 mix. The problem is although it lays a nice bead, it’s a very high hump when test welding on flat surfaces. This is a pain...
  4. F

    Gleaner L3 engine

    What engine is in this thing? Looks like what’s in the 7000 series but not exactly. Has weird Bosch pump on it. Thanks for any info.
  5. F

    New tractor without DEF as a selling point?

    It was a Mahindra commercial on my YouTube feed. There was a list of features but non-DEF was all that I saw cuz I didn’t pause it fast enough, and can’t backtrack the commercials to see it again. How is a non-DEF engine legal in today’s technological climate? I thought it might be a weight...
  6. F

    1996 dodge Cummins injector pump.

    Was called in after customer did a fuel filter change now can’t get high pressure fuel out of pump. I have solid low pressure fuel into and out of pump. Shut down solenoid operating correctly. The filter they took off was rusted where it threads onto the post, and there was water in the...
  7. F

    Question on 200 final drives

    Need to remove bull gears. Book says to press axle out of housing using lots of expensive-looking pullers. My question is , is there any reason I can’t just sling the axle housing and unbolt it from the center housing? Or, is the spline actually pressed into the gear? Thanks, Fritz
  8. F

    Question on F2 Gleaner Corn Plus

    Is there an adjustment on the header control valve to control the drop rate? Is impossible to slowly lower the header with the lift lever.
  9. F

    Re: International 203 Combine

    Was just checking to see if you still wanted the information.
  10. F

    Early 4000 , no 3-point action

    Owner says action became sluggish during the day, pulling a mower. Stopped for the day , came back next morning, no hitch operation at all. Unit is 60 miles away, would like to take a pressure gauge and whatever tools you guys suggest. Ive never been close to a 4000 that wasnt a backhoe, but...
  11. F

    R or 830 carburetors

    I have been searching for a carburetor for a caterpillar D4 starting engine. I am getting rumors that the John Deere starting engines use the same Zenith TU4C carburetor. Can anyone confirm this theory? The carbs are out there but in finished condition for $700; I was hoping to find a fuel bowl...
  12. F

    Update on my Chevy v-6 tbi

    It turns out the injector wires disappear into the loom ; I found it was easier just to spend a little time carving a block out of a piece of mud flap and drilling holes for the wires, rather than try to figure out how to make it run with the injectors unplugged. Thank you to all who contributed.
  13. F

    Why is my compressor always full of water?

    I have a single stage Quincy, 12 CFM, that my dad bought new in 1952. The oil in the crankcase always looks like the day the factory put it in. I sometimes wonder if changing the oil is of any explainable value. My problem is with a home-built unit with a 2-stage DeVilbliss , 18 CFM. The...
  14. F

    Chevy 4.3 tbi

    Have this engine in a forklift, equipped to burn propane. Gasoline injectors disconnected and plugged. Do the wires need to be connected to the injectors for the engine to run? My problem is the grommet for the wires is gone, someone had glued the wires in with RTV. This recently gave way and...
  15. F

    Re: Convert Farmall F12 Steering to F14 with higher post

    Probably steer hard, binding in the bushing.
  16. F

    I.D. Skid loader

    Who built this thing? $2500, ran when parked.
  17. F

    Customer States....

    My temperature gauge on my 4500 stays in the red after a few minutes... I want a new gauge.
  18. F

    Ford crawler

    Is this a kit or a one-off tool room piece? Or was it actually built in numbers?
  19. F

    Re: Ford 555D - Rebuilding Engine - Parts Help/Confirmation

    I have a core motor , Ill lift the valve cover tomorrow and post a picture if you like . That really does look high.
  20. F

    Teddy

    Havent seen him around here lately, anyone know how he is?
Tractor Parts Tractor Manuals

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top