(800) 853-2651
SHOP NOW

Search results

  1. F

    Brazing Nut onto Stripped Farmall 140 Steering Box Mounting Hole

    You need a clear area at right angles to the repair hole, and sufficient height clearance to get your drill in there to drill for the Heli-Coil tap. I doubt you will have room for a tap wrench, but there are 3/8” square drive tap sockets so that you can start the tap with an ordinary ratchet...
  2. F

    Frozen clutch - dissolve rust with Coke?

    It penetrates the same way as when a guy waits for months for some magic potion to penetrate between a piston and a cylinder wall . The guy wakes up every morning expecting to turn his engine because someone online said, “I freed up hundreds of engines like that, and it has never failed me”...
  3. F

    IH 806 diesel engine

    It may not need a total rebuild, depending on how it locked up. Take it apart first and see what is wrong with it. Then you can determine whether you want to pursue an overhaul.
  4. F

    international #10 grain drill soy bean settings?

    If no seed chart, a few simple mathematical calculations is all that is needed to calibrate the drill accurately Calculate the length of a pass that would be required to plant 1/10th of an acre. The number of openers and row width will have a factor on this distance . Paint a white stripe...
  5. F

    bushing replacement, Farmall M

    If the bushing is soft enough to thread, just drill the whole thing out and forget taps and pullers.
  6. F

    Cub Cadet 122 . Has anyone made their own hydraulic lift ?

    The piston travel will be determined by the length of throw of your manual linkage. The various cylinders available for this application are about 1-1/4” bore.
  7. F

    Vintage Chainsaw Fuel Mix

    So the API service classification is a lie?
  8. F

    Who sells the best QUALITY condensers?

    I have 100 Valley Forge condensers from the sixties of various part numbers. Post your dimensions and I’ll go through the boxes and see if I have a match.
  9. F

    super c generator issues..maybe normal, hot

    If you have a non-vented generator, it’s going to run hotter than anything else. Mine charges the exact same numbers you have stated and runs hot enough that you can’t keep your hand on it for very long. I grew up with this tractor and it’s done this for 50 years.
  10. F

    Installing temperature sensor in 560

    I didn’t think of that, that should have worked. Definitely never encountered this before.
  11. F

    Installing temperature sensor in 560

    Well if it screws together again normally after removing the adapter from the head, I’d just put some pipe dope on the threads and thread it back in the the head just enough so it doesn’t leak. The retainer nut is so far away from the compression area it seems strange that it would do that.
  12. F

    Someone shot my cat

    In all actuality, the cat probably was on someone else’s property and some **** ****** probably shot her. My issue is the flat denial that it could possibly happen the way I said it could, since we have had a handful of animals killed on our property since I was a kid… and this was in the...
  13. F

    424 International Hydralic Lift

    Do you mean it works when cold and then slows/stops when warm? One possibility is the pump is self-destructing and the gears are milling into the pump body; if you take the inline filter apart and it full of aluminum, the pump is shot .
  14. F

    Someone shot my cat

    Doesn’t matter what “ sounds reasonable “ to me. I want convincing evidence if I’m called on to judge somebody. It would be “reasonable” to assume that you would have shot the cat yourself, given the chance, since you have already proclaimed your dislike for cats. You’re biased. You have...
  15. F

    Someone shot my cat

    Many of you seem to be under the assumption that the cat was on someone else’s property. How do we know this? She was found at home in her own barn. Not possible some kids walking around the woods (someone else’s woods) with a pellet gun, killing all the song birds the cats missed, and the...
  16. F

    Beware of Thief/Scammer

    See what you get for trying to do a good deed?
  17. F

    424 International Hydralic Lift

    There are 2 filters. One is an in-line cylindrical across the top of the trans at the bottom of the dashboard and a strainer on the end of the suction line that pushes into the lift cover. Air should not be a problem unless it is being sucked into the system via bad suction tube connections...
  18. F

    Hydraulic Remote Valve

    Judging by that chamfer on the end of the spool I’d pull the spool out and look in there again. The O-ring is probably mashed flat and hardened to the shape of the groove and difficult to see.
  19. F

    Vintage Chainsaw Fuel Mix

    This is not the first time I’ve seen this lean of a ratio. I was on a golf cart forum when I first heard of this and I simply didn’t believe it was possible. But they discussed it like it was no big deal, which apparently, it wasn’t. I have no issues running old two strokes at 50:1 .
  20. F

    460 Power Steering Line Blows

    I didn’t get a close look at it before… did they actually try encasing that line in JB weld?
Tractor Parts Tractor Manuals

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top