(800) 853-2651
SHOP NOW

Search results

  1. M

    Case 420b starter

    I'm working on a 1959 Case 420B tractor/loader/backhoe with the case omatic transmission. The starter nose cone broke off and put all the drive teeth into the bell housing. I can't find a starter to replace the MDL6019 autolite/prestolite part number. Parts book also shows Delco #s 1107755...
  2. M

    duplex carburetor load screw thread

    I took the load screw out of my 530 carburetor and the threads are messed up. Does anyone know what the thread size and pitch is so I can get a tap to chase the threads in the carburetor. Thanks for your help!
  3. M

    zenith carburetor experts

    I have a zenith 63awll updraft carburetor on a tractor that came off a 248 chevy. It's currently on a 283 waukesha. It works good and lugs fine, but can't get enough fuel out of it under load. I drilled out the main jet some, but now that affected my idle circuit. It over fueling at idle no...
  4. M

    The 2155 doing what it does best, pulling

    Here's a video I thought some of you may like of the our old 2155 pulling as it has been since the early 80's 2155 pulling
  5. M

    Jubilee ignition troubles

    I overhauled my buddy's Jubilee about 6 years ago. Put all new plugs, wires,condensor in at that point and ran fine until about 1 year ago. Replaced points, condenser, coil, plugs, etc again. Starts up cold, runs, let it warm up some, work it and spark starts fading watching a spark tester...
    • mkuhns
    • Thread
    • Replies: 7
    • Forum: Ford
  6. M

    310 gas liner 3-15/16

    Does anyone know of any replacement liner for the 3-15/16 pistons for the M&W pistons for an 1850 gas. The 3-7/8 liners bored out seem to crack fairly easy. Also does anyone know of any sleeve manufacturer making a 4" liner for the 310. I have a set of 4" M&W pistons I would like to put in...
  7. M

    1020 scv issue

    I have a early 1020 with the old style scv. When I use the one valve that tilts my loader it wants to keep feeding oil for a half second or so letting the bucket keep tilting. Since I know it does this sometimes, I can reverse the valve lever and bring it back and sometimes it just wants to keep...
  8. M

    Kewanee Blade color

    Does anyone know of a color that would be close to the original for a Kewanee 167 or 168 blade. Its a shade of yellow to gold. I would like to match it with something that might be close from tractor supply. It's hard to tell what the color really was from 50 years ago. Any help would be...
  9. M

    1020 3pt hitch balls

    Is there an easy way to repair the 3 point hitch where the balls fit in. Mine are worn on the arms where an implement would hook to, and on the link to the rockshaft. The arms slip over the balls. I see TSC has some repair ends that you cut off the end where the ball fits in, and weld the new...
  10. M

    JD 1020 brake failure?

    I've been cleaning metal out of the rear of my 1020 that my grandfather got repo probably in the early 70's. I assumed all the fine metal that was in the rear came from spider gear failure about 20 years ago and just not cleaned out properly. I removed both axle housings to clean them out and...
  11. M

    1020 countershaft friction plug thickness

    I had to take the low, reverse countershaft out of the trans. I was wondering what the thickness of the brass on a new plug would be. Mine are worn somewhat crooked also. My pilot bearing was partially seized, so I don't really know how well they were working as a brake.
  12. M

    1020 engine serial #

    I have a 1020 that supposedly the engine was replaced long before my time. I was wondering if there was a way to tell if the engine serial# matched the tractor year. Tractor is a 1966 year model and the engine serial # is SNM41TR030645T. I looked online and couldn't figure out what the 41T...
  13. M

    jd 1020 clutch

    I have a 1020 with 2 stage. Factory was a 10" clutch. Looks like there's enough room to put an 11" in. Will this work OK.
  14. M

    1020 power steering pump

    I have an early 1020 that had a hydraulic system contaminated with metal. The transmission screen had a whole in, and the main filter was being bypassed due to the cone at the bottom not holding the filter against the transmission case. So the metal went through the transmission, power steering...
  15. M

    Oliver tractor auction and other antique vehicles

    Just wanted to let you guys know about an antique tractor auction here in Central PA near Lewisburg. This guy has a real nice collection of tractors, most restored. He has about 15 Olivers, a bunch of other antique tractors, cars and trucks. Click on the link for full listing and pics from that...
  16. M

    70 diesel head

    I have the head off my 70 diesel because of pressure in rad. I pressurized both cylinders and #1 left air into the radiator. Anyhow the head gasket was leaking compression only and the head is grooved and will need resurfaced. Can the injector tubes also allow compression into the cooling...
  17. M

    ford 4000 holley carburetor

    I know there are a lot of issues discussed on this forum on these. I just want to confirm what I thought I read through the archives. Before and after overhauling the engine on a friends 4000 it wouldn't idle without the choke being on half way. I tore the carb apart and flushed out the idle...
    • mkuhns
    • Thread
    • Replies: 3
    • Forum: Ford
  18. M

    201 gas valve recession

    What is max allowable valve recession for a 201 gas or what would one consider too much? I looked on here and the internet and couldn"t get a clear answer. The intakes are around .070" and the exhaust are about .100" Thanks in advance
    • mkuhns
    • Thread
    • Replies: 0
    • Forum: Ford
  19. M

    4000 losing hydraulics

    Is it a common problem to lose hydraulics going up or down steep hills with these tractors. This 4000 has the independent PTO with they hydraulic pump mounted on the right side of the rear. The oil level is where it belongs and not running between the trans and rear. Oils stay separated. Do...
    • mkuhns
    • Thread
    • Replies: 5
    • Forum: Ford
  20. M

    Ford 4000 cylinder spec

    Sorry for the repost, I accidently posted in the fordson forum. I have a 1966 Ford 4000 that has a 192 gas in that I'm overhauling because of blowby. #3 piston has two rings broke and top one partially missing. At what point is it still permissible to use std pistons. The bores aren't torn up...
    • mkuhns
    • Thread
    • Replies: 10
    • Forum: Ford
Tractor Parts Tractor Manuals

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top