(800) 853-2651
SHOP NOW

Search results

  1. R

    high altitude motor

    What is the compression ratio of a 226 ci motor in a wd45?
  2. R

    Model G tractor

    Is the number one engine cylinder at the crank shaft pulley or at the fly wheel end of the engine?
  3. R

    D17

    What is the factory rating lifting capacity of a series 4 when new with the AC loader installed?
  4. R

    Amp gauge

    What would cause the amp gauge to jump back and forth when engine rpms is above 1/4 throttle. Replace generator and cut out but the gauge still jumps back and forth. 1939 Wc 6 volt system. new or old battery makes no difference on the gauge action.
  5. R

    lift arm latches

    How many different styles of lift arm latches was made for the WD/WD45 and d17 tractors?
  6. R

    WD45 Diesel

    How many pounds is the cooling system pressure cap? 4 or 7 lbs?
  7. R

    AC B motor

    How much oil should the valve rocker arms be getting? Oil pressure gauge needle is setting on the R[normal] at about 1/4 throttle setting. Can not see any oil running off of the rocker arms. Checked oil passage to rocker arm is not plugged up.
  8. R

    plow day

    Went to one yesterday, around 25 tractors of all colors. three of them were quite unique a 1935 Case model unknown, a model A John Deere on all steel wheels, Allis Chalmers WD45 Diesel. Even a newer John Deere front wheel assist with cab and loader with a two bottom plow, guessing around 35/40...
  9. R

    wd45 power steering

    Can a thin hydraulic oil be used in a Char Lyn power steering system, with the Allis Chalmers factory pump and char lyn torque generator?
  10. R

    D17

    Will cat 2 quick hitch hook up to a series 4 D17 with factory 3 point, with out making any changes to either of the componets?
  11. R

    Re: Gasoline Carburetor to Replace My KGn1 Dual Fuel System

    Use a M S 464 carb on your WD45 as that is what was on most of them when new.
  12. R

    Trailer ramp mesh question.

    This message is a reply to an archived post by JayinNY on May 23, 2020 at 19:25:09. The original subject was "Re: Trailer ramp mesh question.". I used the metal mesh from hog crate floor on my trailer beaver tail, very heavy does not bend when heavy loads are on it.
  13. R

    Wd rpm

    To increase the engine rpms on a Allis Chalmers 201 engine do I bend the governor cross arm towards the radiator or back away from the radiator?
  14. R

    201 engine

    Will a MS carburetor from a WD45 give a 201 ci with factory standard pistons any more power? Or will it only overload it with fuel?
  15. R

    front wheels

    My loader tractor has a narrow front end, has a 6ft bucket on it, will turning the rims with the dish side out cause any problems with them cracking or breaking with the bucket full of heavy material. This time of year I am fighting the mud balling up between the tires.
  16. R

    D17

    Any one have a problem with their s4 gas d17 eating starters? About once a year the starter on mine breaks the drive. It has a loader on it, but may set for several days with out being started. Even replaced the fly wheel ring gear.
  17. R

    tractor fuel tank

    Having problems with rust clogging the inlet on fuel sediment bowl, what is the best way to remove the rust and crude in the tank? What is a good sealer to use once tank is clean?
  18. R

    B hydraulic

    On my 1950 AC B the hydraulics works good for lifting, but will not stay in the raised position settles down fairly fast. What is the problem, and how to fix it too hold up the implement? Tried adjusting linkage with no change in holding up implement.
  19. R

    horse power

    What is the PTO horse power of a IH 656 gas tractor?
  20. R

    snowblower

    What would the ideal size snow blower be for a 50 horse tractor in about 2ft or less of wet heavy snow? Witch one is best, a single stage or a 2 stage blower?
Tractor Parts Tractor Manuals

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top