(800) 853-2651
SHOP NOW

Recent content by RobCons

  1. RobCons

    Ford 641 Carburetor Float, Has Me Pulling My Hair!

    Is the float leaking, getting fluid inside it, or the valve letting fluid leak past it?
  2. RobCons

    110 volt welder recommendations

    I have Lincoln machines, one 120v, and like the brand. Realistically as far as the major name brands go its just what you get used to. About like Chevy, Ford, etc.
  3. RobCons

    Sharpen bush hog blades

    I use a 4.5 inch angle grinder, raise the bush hog up with the 3 point lift and support it with a heavy steel saw horse.
  4. RobCons

    12V Sprayer pump flow and pressure question

    I would cheat and look at some of the store bought models of similar size and go from there.
  5. RobCons

    Dowsing Rods

    I usually have a pair in the truck made of welding rods bent at 90 degrees. Works to find water, phone, and electrical lines.
  6. RobCons

    Best tool for this risky cut in metal

    I used a grinder with a cutoff wheel to put an access panel in the bed of my Silverado. I was able to get a welding blanket between to tank and truck bed for the sparks. Then welded tabs on the removed section so I could just set it right back in place.
  7. RobCons

    Zero turn mower

    A little fabrication work for a bracket and you could probably install small electric fans to blow across the hydraulics.
  8. RobCons

    4 1/2 in grinding discs

    I'm also a flapoer disc fan, especially for sharpening mower blades. I clamp the blade in a vise and use both hands on the grinder.
  9. RobCons

    Did you use your tractor today?

    No pictures but used the Ford 4cyl 4000 to plow up a small garden for a neighbor.
  10. RobCons

    Looking for a new toy

    We like our TX Gator. Its old, has 1800 hours, but still looks goid and runs like it should.
  11. RobCons

    Bucket for loader

    I agree with Tony. Hop online and order a pair of skid steer universal quick attach brackets. Cut the pin mount brackets off your trashed bucket for reuse.
  12. RobCons

    Need some help

    On lots of these old tractors dont worry about wire color as much as where its coming from and going to. Many of the wires have been replaced or spliced with whatever wire was handy. For lights I would use a red wire and a black one.
  13. RobCons

    Average age of user

    61 trips around the sun for me.
  14. RobCons

    Funny tractor sayings... What can you come up with?

    I feel boxed in!
  15. RobCons

    How to make and use a PHD goal post rack

    Mine sounds like DeltaRed's. It hangs from a chain.
See more
Tractor Parts Tractor Manuals

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top