(800) 853-2651
SHOP NOW

Recent content by mikewood869

  1. mikewood869

    Kory 5566 running gear wheel bearings

    I did call them, and the bearings are the same price as the bearing shop. It looks like its cheaper to get that kit than to get the bearings and seal separate
  2. mikewood869

    Kory 5566 running gear wheel bearings

    I was starting to figure. The seals won't be into Wednesday. I thought the seals were going to be special but they aren't. I can eat put of that hub. I take it I can't put # 2 grease in it and just grease the inner bearing and work my way out? It looks like the hub is going to take a tube of...
  3. mikewood869

    Kory 5566 running gear wheel bearings

    I decided to repack the wheel bearings on a Kory 5566 running gear and add some grease zerks. I took off the front left hub and the inner bearing in the hub spun. I got the bearing not to spin. Anyways... Anyone know if there is supposed to be a gap between the bearing and the seal? There is...
  4. mikewood869

    1966 Ford 3000 power steering cylinders

    Sorry, I use the all in one pump, I assume that was for the reservoir under the hood? I take it’s part 16 then? The power steering setup came off a 3400 3400 Power steering pump
  5. mikewood869

    1966 Ford 3000 power steering cylinders

    Completely different tractor. Don't know how you found this post. To finish up on this thread, the pump is putting out too much pressure. It is putting out 1100 psi if I remember correctly. I'm not sure how to change the pressure. I switched out the new pressure relief valve with the old one and...
  6. mikewood869

    Ford 4500 gas engine in to ford 3400

    Direct swap. We did a 4500 diesel swap on this gas 3000 and we had to change a few things since it was going to diesel
  7. mikewood869

    3550 engine swap.

    Yes you could swap in a gas engine. It would be cheaper to rebuild the engine your self unless the block is junk or you can’t find a block. To rebuild our 6610 motor was a tad under $3000; boarded (head was decked), head was decked, engine rebuild kit, new rods and pistons
  8. mikewood869

    NH 315 Baler

    We've used a Ford 4110 on ours. That tractor has pulled the baler with a kicker and a full wagon on hills just fine
  9. mikewood869

    Tim Daley passsing

    Sorry to hear, he seemed like a great guy with a lot of information. RIP
  10. mikewood869

    1980 Ford F700 370 engine to 1995 Ford 429 engine

    Looking to swap a 1980 370 to a 1995 Ford 429, is there anything to watch out for? I assume just pull off most of the wires so I can get spark
  11. mikewood869

    Preferred transmission in a 1988 3910

    Probably the dual range 8x2 would be the cheapest to rebuild. I have the 8 speed synchromesh, 8x4 in my 2910 and it works good.
  12. mikewood869

    Ford 3400 power steering cylinder line seal

    It is, I robbed the column, cylinders, and pump off a 3400 and put it on a 3000 ag chassis
  13. mikewood869

    Ford 3400 power steering cylinder line seal

    Anyone know if you could if this seal or ring is supposed to come out? I was working on the right cylinder and one of the ring/ seals were missing. Part number: 358774S, 4a. The picture is the left cylinder. Power steering cylinder diagram
  14. mikewood869

    Ford 3000 Holley carb, what’s it’s made out of

    Anyone know if you could wield on a Holley carb r11411a. Is it aluminum or white metal?
  15. mikewood869

    Ford 3400 power steering cylinder and lines

    Before I put a 3400 power steering cylinder back on a Ford 3000 tractor to see if it works, does anyone know if the cylinder rod when extended, will be too long? This is on a 3000 style front end. Also I still don't have one of the cylinders yet (having it rebuilt since I couldn't get it apart)...
See more
Tractor Parts Tractor Manuals

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top