(800) 853-2651
SHOP NOW

Recent content by mhb@ufe

  1. M

    Ford 2000 Power Steering Asst. Cylinder Disassembly

    I was going on the assumption you had half inch rods. New Holland lists part number FP541 for the 5/8 rod with the welded cylinder and I don't see that available on this site...
  2. M

    Advice on 3 pt pallet fork

    I had a set of adjustable ones on my old style 4000 and always left the set out and they were only 36 inches wide. I did make up a hydraulic top link which made them much more user friendly.
  3. M

    Ford 2000 Power Steering Asst. Cylinder Disassembly

    The correct kit would have an inner seal, bushing, outer seal(wiper seal) washer and snap ring. All are installed over the rod as the rod cannot be removed without cutting the cylinder. The part number for the correct kit is CAPN3301B and it can be purchased from this site.
  4. M

    Pulling with your 9,2 or 8N

    I pull with a 1942 2N and does quite well in the 2500lb class and a 1948 8N that does ok in the 3000lb class. All the pulls I do are for non modified antique tractors.
  5. M

    CNH parts, online catalog

    https://www.mycnhstore.com/us/en/newhollandag/ Type 2000 where it says search parts catalog.
  6. M

    Ford 801 shift lever removal

    It is on a tapered shaft with a woodruff key. Try tapping up on the lever down close to the base.
  7. M

    Tractor question that's really about implements

    I agree with MJMJ, the 19 hp would run it but that tractor is way to light and the baler will push it around. It is also very unlikely the 501 mower will fit as the sub compacts have a limited 3 point hitch.
  8. M

    Needing part for 268 NH baler

    This is what he is referring to. You get the correct sprocket and the weld in hub that will fit the shaft. https://redboarchain.com/products/40x23-weld-sprocket-for-x-series-weld-hub-23-tooth
  9. M

    Ford 2000 offset ID

    Here is an earlier post of someone that had a 1966 4cyl 2000 offset. https://forums.yesterdaystractors.com/threads/ford-2000-offset.1026531/
  10. M

    Ford 2000 Offset ID

    Here is an old post of a discussion on someone that had a 1966 4cyl 2000 offset. https://forums.yesterdaystractors.com/threads/ford-2000-offset.1026531/
  11. M

    Ford 2000 Offset ID

    If it is an offset the transmission may have been replace and those numbers represent the donor tractor.
  12. M

    Ford 8n Freeze Engine Plugs

    The rubber ones will not fit properly in the N series tractors.
  13. M

    4500 TLB brake rod seal

    The brake rod cannot be removed from the out side however you can replace the seal without removing the rod.
  14. M

    3930 oil leak

    The grove on the bottom is there as a way to move the tube. You may need to move the tube down a little to access the snap ring.
  15. M

    Ford 555 water pump pressure

    Water pumps do not create the pressure in the cooling system. The pressure is created by the rising temperature of the coolant. It's possible the thermostat is stuck closed preventing flow.
See more
Tractor Parts Tractor Manuals

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top