-
jon f mn replied to the thread 1030 Case PTO.I think you will find the spring broken for that pin. -
jon f mn replied to the thread 1030 Case PTO.I'm not sure on the measurements, but most everything from the taper in should be hidden when locked. When pulled there may be half an...
-
jon f mn replied to the thread 1030 Case PTO.I would take the cover off the side and inspect the clutch carefully. There are parts that can fall off and get under the bull gears...
-
jon f mn replied to the thread Case front end question.Those are different. The round nose 400 takes the larger front from anything from the 400 to the 1030. The later fronts with the pipe...
-
jon f mn replied to the thread Railroad fixed the culvert.They just send a track hoe that ran down the tracks and dug out under the tracks. They left the tracks hang and put the new culvert...
-
Looks like the rr was good to their word, mostly. If you remember the plugged the culvert and flooded my land. They originally said...
-
-
jon f mn replied to the thread Broken spindle.Just get a couple 4x4s and put them under the bucket and slide on them. You can cut a small notch in them for the cutting edge, or even...
-
jon f mn replied to the thread Case 511B Steering.Call external_link in new York, they should have those for you. They are great folks to work with on anything case. I just got a full...
-
jon f mn replied to the thread 611 B torque converter rebuild part 5.Looking good Chuck! When I did mine I read the manual first, then again before I started reassembly, and still had to repeatedly go back...
-
jon f mn replied to the thread My 190 gets a new drive motor..I'm jot sure, I know there are several different ones just on the case mowers.
-
jon f mn replied to the thread My 190 gets a new drive motor..I called them first and they don't have one for the 190. They do for most other models tho.
-
jon f mn replied to the thread Case 1070 Clutch.both problems are adjustable for someone who knows what they are doing, sadly that's not me. Go down t the case forum and ask there, I'm...
-
I bought this 190 tractor last year and been trying to get it going. Runs good, but the drive motor just wouldn't pull going forward...
-
-
jon f mn replied to the thread Best Looking Case.That is tough, tye 830 ck is pretty sweet. The black knights are also sweet, but the black and white 94 series are about as pretty as it...
-
jon f mn replied to the thread What Case planter is this?.I don't have a book, but I'll ask around. I know that you can use IH plates in those units with an adaptor.
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.
Copyright © 1997-2024 Yesterday's Tractor Co.
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.
Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy