-
JYesterday I took off the shifter cover and put a new gasket on it. I didn’t think there was one on it, it appeared to be leaking around...
-
JJim in LA replied to the thread Picked up my second 8N today.I took the shifter plate off mine this afternoon to replace the gasket and see what things look like in there. The front bolts are a...
-
JJim in LA replied to the thread 8N no oil pressure.You haven’t got “the fever” yet. Don’t give up on it. Your tractor looks great cosmetically. Look at a some of the 8N repair and...
-
JJim in LA replied to the thread Bad starter button?.Dan and Rachel Gingel show how to replace the starter button on one of their videos where they convert 8N from 6 volt to 12. I was going...
-
JJim in LA replied to the thread Picked up my second 8N today.After overhauling my Dad’s old ‘49 two years ago I found a ‘51 for sale for $800 and bought it. I had to replace all necessary external...
-
JJim in LA replied to the thread pto replacement.That #4 shaft is for tillers and finishing mowers and maybe 4 ft rotary mowers.
-
JJim in LA replied to the thread pto replacement.Have you checked Agri Supply? I purchased two class or group 4 shaft assemblies with slip clutch from them pre 2020 at very reasonable...
-
JJim in LA replied to the thread Looking for yard tractor.I think it means they are best suited for a gravel/dirt yard or a lumber yard. Not to be confused with a lawn tractor.
-
JJim in LA replied to the thread Left-turn motorcycle collisions.A ‘65 Chevy Belair totaled by a little ol Honda 90?! I guess the stars and planets were aligned just right that day.
-
JJim in LA replied to the thread PTO housing help.I had the exact same problem when I upgraded to the 1 3/8 shaft. I could have taken the time to grind that ridge down a little but...
-
JJim in LA replied to the thread Never underestimate what can be used as a tool lol.
-
JJim in LA replied to the thread Alternator adjustment bracket.Your going to need some more brackets. Look at 8n parts on this site and check out the electrical system section, there are several...
-
JJim in LA replied to the thread Anyone attempted to use JD's new parts site?.I was able to navigate through it and find parts for my 5105 and 3005 without too much difficulty using the model numbers and parts diagram.
-
JJim in LA replied to the thread fixing ford 8ns.1951 8N I bought required the following just to get it running to see what all it did need: All new valve train,starter,wiring...
-
JJim in LA replied to the thread ATV/lawn mower hydraulic lift.I have one of the Harbor Freight lifts I bought about eight years ago. Only cost about $70 back then. Only problem lifting my Gravely ZT...
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.
Copyright © 1997-2024 Yesterday's Tractor Co.
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.
Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy